Hyundai Genesis Equus ECS (Electronic Controlled Suspension)

What is the ECS automatic height adjustment system and how does it work?

Pneumatic height adjustment system, car height adjustment price with remote, height adjustment repair kits price, Genesis Pars height adjustment, height adjustable shock absorber, car height adjustment

تقویت هندلینگ و زیربندی خودروهای ریس,نرم کردن کمک فنر

تقویت هندلینگ و زیربندی خودروهای ریس,نرم کردن کمک فنر

ECS (Electronic Controlled Suspension), automatic height adjustment system

This system, which is present in Hyundai Genesis and Centennial cars, allows the car to automatically adjust the pneumatic height. In these cars, the height of the car can be adjusted in three modes: high, normal and low. At speeds of less than 70 km / h you can manually change the height of the car from normal to high. Of course, by increasing the speed of the car from 70 km / h, the altitude automatically returns to normal. But the low mode is only automatically set at a speed higher than 12 km / h, and if the car speed drops below 80 km / h for more than 50 seconds, the altitude returns to normal. .

Hyundai Genesisi Equus Centencial 2009 2016 Air Suspension Compressor Pump

Hyundai Genesisi Equus Centencial 2009 2016 Air Suspension Compressor Pump

After repairing the Genesis suspension or replacing its parts, the system will be out of calibration and error code C1620 will fall on the ECS system. To calibrate this system, no error code other than C1620 must be available and the air pressure and mass inside the system must be sufficient and standard. Note that to calibrate the Genesis suspension, the tank air pressure must be more than 7.5 times and the system air mass must be 93 to 122 bar and there must be no error code in the system except for the calibration error (C1620). .

Air-suspension-cystem-with-shock-absorber-strut,-compressor,-air-valve

Air-suspension-cystem-with-shock-absorber-strut,-compressor,-air-valve

Special operation of the sexual suspension system

After connecting the diagnostic device to the vehicle and entering the ECS section, select the special settings option.

1. Auto Detected Configuration Reset (ECS)

If the control of the ECS unit is changed, it needs to be reconfigured for the mentioned vehicle, and if this operation is required, you will see error code C1702. To do this, the following conditions must be met:

The switch is open and the engine is off.
The car is stationary and motionless.
2. Check the performance of the aids and the interface valve (Air Filling / Venting Setup)

This option is used to inflate and evacuate the ECS tank, and using the menu, allows the user to fill and discharge inflatables individually and simultaneously.

Hyundai-Genesis-Rear-Dust-Cover-Boot

Hyundai-Genesis-Air Spring Suspension airmatic pnevma pneumatic pillow Rear-Dust-Cover-Boot

Important note :
During this operation, the car should be placed on the jack and none of the wheels should be in contact with the ground.
The switch is open and the engine is off.
The car is stationary and motionless.
Connect the air filler hose to the ECS tank valve and fill the air inside the tank. Due to the lack of automatic tank filling device, this operation is done manually by the air pump gun series.
3. Checking the ECS system (checking air pressure system)

خراسان رضوی کمک فنر بنز ,اصفهان تعمیر کمک فنر جنسیس,تبریز کمک فنر بنز,کمک جنسیس, کمک فنر جنسیس,عمده فروشی تهران کمک فنرجلو

خراسان رضوی کمک فنر بنز ,اصفهان تعمیر کمک فنر جنسیس,تبریز کمک فنر بنز,کمک جنسیس, کمک فنر جنسیس,عمده فروشی تهران کمک فنرجلو

In this case, the switch should be open and the car engine should be off. By creating the above conditions, the system starts checking the system pressure as well as the operation of the overhead valve, height sensors, circumferential valve and و. If the system pressure is correct, the following parameters are displayed.

System Air Mass: 93 – 122
Air Mass Reservoir: 36
Reservoir Pressure: 7.5

Note: If you change the control unit and display error code C1701, you must select the following option.

finish service mode

4. Height Sensor Calibration

In this part of the special operation, the height sensor is reset to normal. In order to perform this operation, the following conditions must be met:

The switch is open and the engine is off.
The battery is fully charged.
System air pressure should be more than 7.5 bar.
Do not put any extra weight on the car.
The air mass of the system should be 93 to 122 times.
There are no other errors in the system except error C1620.
The height setting should be in the normal position.

5. Height level control select

In this section, it is possible to select the height of the car in three modes: high, normal and low.

خراسان رضوی کمک فنر بنز ,اصفهان تعمیر کمک فنر جنسیس,تبریز کمک فنر بنز,کمک جنسیس, کمک فنر جنسیس,عمده فروشی تهران کمک فنر

خراسان رضوی کمک فنر بنز ,اصفهان تعمیر کمک فنر جنسیس,تبریز کمک فنر بنز,کمک جنسیس, کمک فنر جنسیس,عمده فروشی تهران کمک فنر

Share this post


Online Service
Live Chat